IC697CPU782RR | 可编程逻辑控制器 | 能够实时控制机械和物料搬运系统
系列 ：90-70系列
零件编号 ：IC697CPU782RR
离散 I/O： 最大 2 K(任意组合)
电压输入： 5 伏直流电
模拟 I/O： 最大 8 K
串口： 3
布尔执行： 每个布尔函数 0.4 微秒
工作温度 :0 至 60 摄氏度
IC697CPU782RR是一款可编程逻辑控制器，设计用于安装在单个机架插槽中。 它能够实时控制机械和物料搬运系统。机架式背板使该器件能够与各种 I/O 模块进行通信。要操作和控制此设备，请使用运行/停止控制开关或带有相应软件的连接计算机。该IC697CPU782具有16MHz微处理器，能够以0.4微秒的性能速度执行浮点计算。该器件可以处理高达 12K 输入和输出以及 8K 模拟 I/O 的各种混合。
IC697CPU782RR 需要存储器扩展板来存储用户数据和程序信息。此扩展板提供高达 512 KB 的易失性存储器和 256 KB 的闪存。易失性存储器由CMOS RAM电池维护。要安装此扩展板，必须首先由连接的计算机初始化 CPU。IC697 LAN 接口模块、IC660 和 IC661 总线控制器、众多协处理器模块、各种通信模块以及 IC697 系列的所有分立和模拟 I/O 模块都与 IC697CPU782 兼容。
此设备由从编程器计算机运行的软件配置。编程不需要拨码开关和跳线。可通过串行或并行接口进行配置。如果安装了适当的硬件，也可以进行以太网连接。需要 MS-DOS 或运行相应软件的 Windows 95 和 Windows NT 计算机才能对IC697CPU782进行编程。密码与内置内存保护键开关一起保护配置设置。
Series: 90-70 series
Part number: IC697CPU782RR
Discrete I/O: up to 2 K (any combination)
Voltage input: 5 volts DC
Analog I/O: Max. 8 K
Serial port: 3
Boolean execution: 0.4 microseconds per Boolean function
Operating temperature :0 to 60 degrees Celsius
The IC697CPU782RR is a programmable logic controller designed to be installed in a single rack slot. It provides real-time control of machinery and material handling systems. The rack-mounted backplane enables the device to communicate with various I/O modules. To operate and control this device, use the run/stop control switch or a connected computer with the appropriate software. The IC697CPU782 has a 16MHz microprocessor capable of performing floating-point calculations at a performance speed of 0.4 microseconds. The device can handle various blends of up to 12K inputs and outputs and 8K analog I/O.
The IC697CPU782RR requires a memory expansion board to store user data and program information. This expansion board provides up to 512 KB of volatile memory and 256 KB of flash memory. The volatile memory is maintained by a CMOS RAM battery. To install this expansion board, the CPU must first be initialized by the connected computer. The IC697 LAN interface module, IC660 and IC661 bus controllers, numerous coprocessor modules, various communication modules, and all discrete and analog I/O modules of the IC697 family are compatible with the IC697CPU782.
This device is configured by software running from the programmer computer. Programming does not require dip switches and jumpers. Can be configured via serial or parallel interface. An Ethernet connection is also possible if the appropriate hardware is installed. MS-DOS or Windows 95 and Windows NT computers running the corresponding software are required to program the IC697CPU782. The password protects configuration Settings along with the built-in memory protection key switch.
